Technical data
Digital laser measure | Zamo |
|---|---|
Article number | 3 603 F72 9.. |
Distance measurement | |
Measuring rangeA) | 0.15–25 m |
Measuring accuracyB) | ±2.0 mm |
General | |
Operating temperature | –10 °C to +40 °C |
Storage temperature | –20 °C to +70 °C |
Relative air humidity max. | 90 % |
Max. altitude | 2000 m |
Pollution degree according to IEC 61010-1C) | 2 |
Laser class | 2 |
Laser type | 635 nm, < 1 mW |
Divergence of the laser beam | < 1.5 mrad (full angle) |
Automatic switch-off (without measurement) after approx. | 5 min |
Weight according to EPTA-Procedure 01:2014 | 0.08 kg |
Dimensions (L x W x H) | 104 × 38 × 23 mm |
Batteries | 2 x 1.2 V HR03 (AAA) |
Battery life | > 3 h |
Battery charging time (HR03, 800 mAh)D) | < 4 h |
Power supply | |
Output voltage | 5.0 V |
Output current | > 500 mA |
Recommended power supply | 2 609 120 713 (EU) 2 609 120 718 (UK) 2 609 120 717 (AU) |
USB Type-C® cable | |
Recommended USB Type-C® cable | 1 600 A01 L6H |
- A)
When measuring from rear edge. In unfavourable conditions such as very strong lighting, a temperature greatly deviating from 20 °C or a poorly reflecting surface, the measuring range can be restricted.
- B)
This applies for high reflectivity of the target (e.g. a wall painted white), weak background lighting and a 20 °C operating temperature; a deviation of ±0.05 mm/m must additionally be factored in.In unfavourable conditions such as strong lighting, great heights or a poorly reflecting surface, and at a temperature of 20 °C, the deviation can be ±4 mm; a deviation of ±0.15 mm/m must additionally be factored in
- C)
Only non-conductive deposits occur, whereby occasional temporary conductivity caused by condensation is expected.
- D)
At an operating temperature of 20 °C
The serial number (11) on the type plate is used to clearly identify your measuring tool.
Adapter |
|
|---|---|
Operating temperature | –10 °C to +40 °C |
Storage temperature | –20 °C to +70 °C |
Relative air humidity max. | 90 % |
Pollution degree according to IEC 61010-1A) | 2 |
Laser line adapter | |
Article number | 1 600 A02 PZ7 |
Width of laser lineB) at a 2 m distance | ≤ 2.0 m |
Length of the laser lineB) at a 2 m distance | ≥ 1 m |
Measuring accuracyC) | ±1.0 mm/m |
Opening angle | ≥ 28° |
Angle for fine adjustment | ±10° |
Weight according to EPTA-Procedure 01:2014 | 0.02 kg |
Dimensions | 38 x 40.5 x 22.3 mm |
Tape adapter | |
Article number | 1 600 A02 PZ8 |
Measuring accuracyC) | ±1.0 mm/m |
Measuring range | 0.005 m to 1.5 m |
Weight according to EPTA-Procedure 01:2014 | 0.03 kg |
Dimensions | 38 x 33.5 x 22.3 mm |
Wheel adapter | |
Article number | 1 600 A02 PZ9 |
Measuring accuracyC) | ±5.0 mm/m |
Measuring range | 25 m |
Weight according to EPTA-Procedure 01:2014 | 0.02 kg |
Dimensions | 38 x 48 x 22.3 mm |
- A)
Only non-conductive deposits occur, whereby occasional temporary conductivity caused by condensation is expected.
- B)
depending on surface characteristics and ambient conditions
- C)
At an operating temperature of 20 °C